Showing posts with label Microcontroller. Show all posts
Showing posts with label Microcontroller. Show all posts

Friday, February 12, 2010

Card Reader Using Microcontroller

Card Reader Using Microcontroller

Card Reader Using Microcontroller

This is a simple version of Card Reader. Why? because this Magnetic Card Reader only in read only environment. It only read the information stored in magnetic card. The purpose of the project is used as card debugger. There are three main part in this project :

  • A reader to capture digital characters from the card
  • A RISC microcontroller to store data and check for errors
  • A display to relay the magstripe contents to the viewer

As processor it use microcontroller AVR ATtiny 2313. For Reader it uses Panasonic ZU-M2121S451 Reader. and for display use LCD 16x2.
"The Magstripe (Track 2) Reader project can be used to view numerics stored a magnetic data card. Although there is no writeback ability, the device is very useful as a card debugger. The treatise will use an LCD character display to relay this data to the user. The circuit uses an AVR microcontroller and can modified to work with similar RISC controllers."
Although the card reader can't write back to magnetic card, I guess this is a one of good reference to learn how card reader work. For download the reference clik here (zip file) or visit this link

Thanks to Brady Mayes for great card reader based on microcontroller.

Monday, February 1, 2010

Electronic Speed Controller based on PIC microcontroller

This microcontroller project built by Chris Spurlock. He try to make a cheap electronic speed controller for brushed DC motors. All cost for this project only take about $15 and a little more brain power and programming on PIC microcontroller.

I though it's a suitable project for people that want to make a simple electronic project based on PIC microcontroller. Here is the schematic for the project and For more detail information.

Tuesday, January 19, 2010

Fireflies With Small Microcontrollers

This circuit simulates fireflies with small microcontrollers. Here is the circuit and the component used for single fireflies


  1. ATtiny13 microcontroller
  2. Light Dependant Resistor (LDR)
  3. LED
  4. 2 resistors
To make it interesting, assembly it on the board for 25 fireflies. Every single firefly is self contained, there is no over-all controller. Here is the picture

Sunday, January 17, 2010

Ultrasonic Spotlight Tracker

Ultrasonic Spotlight Tracker
The ultrasonic spotlight tracker is a system that uses a wireless beacon to track a target’s location using both RF signals and ultrasound waves. It then drives a light source to point at the location of the target.
In this project, we limit our remote unit’s degree of freedom to two dimensions to prove the concept, although it can be very easily extended to three dimensions. To locate the target, we need to measure the distance of the target from at least two known points. The distances are measured by counting the time it takes for sound to travel from the target to the base station and multiplying it by the speed of sound waves. The speed of sound in air is about 334 meters per second. The 16 MHz microcontroller avr can count time intervals on the order of 0.0625 microseconds, which gives a theoretical accuracy of 0.02 mm.

Tuesday, January 5, 2010

Windmeter using Microcontroller

Windmeter using MicrocontrollerWindmeter using Microcontroller

The Windmeter is an anemometer designed to measure and record wind speed distribution from 0 to 17+ meters per second. It was designed for high reliability, ease of construction, and for a wide environmental range. Data is logged over a period of 30.46 days (1/12 of a year), and then saved for 11 months. The data can be retrieved with a laptop computer any time within the 12 months of logging. The Windmeter is self-powered by a solar pannel and battery. Calibration of the Windmeter can be done against a car's speedometer or better yet a GPS receiver. The Windmeter should cost you under $300 to make.

Friday, October 23, 2009

dsPIC 33F128MC706 NUE-PSK Digital Modem

dsPIC NUE-PSK Digital Modem

PSK31 is one of the latest communications modes to capture the interest of hams worldwide. Its inherent ability to dig out low, near-inaudible signals is ideally suited for low power QRP enthusiasts. The PSK31 digital modem engine, however, requires intense DSP processing that is only commonly available in PC sound card. Thus the PSK operator desiring portability for field operation is locked into using a laptop computer as a controller, which results in a cumbersome station.

This project shows you design and construction of a standalone, battery-operated digital modem using a Microchip dsPIC microcontroller. The project includes a character display for transmit and receive text data, and a graphic display showing band spectrum and tuning indicator. Using GPL open source software, the modem can be homebrewed for less than $50 parts cost. When coupled with an SSB-capable transceiver or with a popular PSK-xx transceiver board from Small Wonder Labs, you too can have an effective portable PSK31 station.

© George Heron and Milton Cram

Download
Project documentation


tag : Digital Modem, PSK, DSP, MCU dsPIC33F128MC706, Communication


Monday, October 12, 2009

PIC Wireless Networks Wifi (Hotspot) Detector

PIC Hotspot detector
This wireless detector project allows you to sense the presence and relative signal strength of wireless hotspots. It is "always on" and communicates the presence and signal strength of an in-range hotspot by way of sequences of pulses - like a heartbeat you can feel. The stronger and faster the "heartbeat", the stronger the wireless signal detected.

This project consists of a microcontroller PIC 12F629, some custom interface electronics, a small vibe motor, and an off-the-shelf Wi-Fi detector from D-Link. The microcontroller periodically "presses" the button on the detector to initiate a reading. The microcontroller "reads" the output from the detector indicator LEDs and uses this as the basis for pulsing out a signal on the vibe motor, which the wearer can feel.

tag : wireless networks, hotspot detector, Wi-Fi strength signal indicator src

Wednesday, October 7, 2009

Microcontroller

The NXP LPC214x microcontroller (IC1) provided with the MCB2140 board is a high-end LPC214x device with advanced ADC, DAC and USB capabilities.

A 12.0 MHz crystal (Q1) provides the clock signal for the CPU.

MCB2140 Board Microcontroller

Monday, October 5, 2009

AVR Digital Clock with Roman Numerals




This digital clock project will display a Roman number instead Hindu-Arabic numeral system (1,2,3... ). The project uses micro ATTINY2313 as main processor and LCD to display the clock. When you turn on the device, it will shows a screen flashes "Tempera tempus" as reminder to adjust the time.


The adjustment is done via the small button.
  • Press and hold the button for about 3 seconds -> hours appear on the screen -> release the button.
  • Press the button again and hold -> the hours advance from "I" to "XXIV" -> release the button on the time right.
  • Wait about 3 seconds -> minutes to appear on the screen.
  • Press the button and hold -> the minutes advance from "nothing" to "LIX" -> release on just minutes.

    Unfortunately, you have to readjust the time after your turn off the power, because there is no RTC in this  project.

    Download schematic and source code here

    AVR Digital Clock with Roman Numerals




    This digital clock project will display a Roman number instead Hindu-Arabic numeral system (1,2,3... ). The project uses micro ATTINY2313 as main processor and LCD to display the clock. When you turn on the device, it will shows a screen flashes "Tempera tempus" as reminder to adjust the time.


    The adjustment is done via the small button.
    • Press and hold the button for about 3 seconds -> hours appear on the screen -> release the button.
    • Press the button again and hold -> the hours advance from "I" to "XXIV" -> release the button on the time right.
    • Wait about 3 seconds -> minutes to appear on the screen.
    • Press the button and hold -> the minutes advance from "nothing" to "LIX" -> release on just minutes.

      Unfortunately, you have to readjust the time after your turn off the power, because there is no RTC in this  project.

      Download schematic and source code here

      Monday, September 28, 2009

      Remote Control using PIC16F84A Microcontroller

      Remote Control using PIC16F84A Microcontroller
      Remote Control using PIC16F84A Microcontroller


      design controls up to 8 devices using a PIC microcontroller (PIC16F84A) connected to the phone line. The unique feature here is that unlike other telephone line based remote control, this device does not need the call to be answered at the remote end so the call will not be charged. This device depends on number of rings given on the telephone line to activate/deactivate devices.

      1. Circuit diagram (designed by www.tronicszone.com)
      2. Parts List
      3. C source code complied using HT-Soft PIC C compiler
      4. Compiler Hex code file to be directly programmed into the PIC

      Instructions for the telephone operated remote switch:

      A) While constructing the main circuit, make sure you use 18pin sockets (base) for the PIC16F84A. Do not solder the IC directly to the board since you may have to remove it for programming. Before you use the PIC on the main circuit, you have to first program it.

      B) To program the PIC16F84A microcontroller:

      There are lots of programmers on the Internet available to program PIC microncontrollers. Given below are links to some free PIC programmer hardware/software:

      * http://www.covingtoninnovations.com/noppp/
      * http://www.picallw.com/
      * http://www.lpilsley.uklinux.net/software.htm

      Note: Programm the chip with the hex file attached above and remember to set the fuse bits to use "EXTERNAL HS OSCILLATOR" mode!

      C) Remove the PIC from the programmer socket and put it into the main circuit socket.

      Set the DIP SWITCH as follows:

      Switch3 Switch4 No. of initial rings to Switch ON(activate half of the board)

      OFF OFF 5

      ON OFF 4

      OFF ON 3

      ON ON 2

      The number of initial rings to Switch OFF is one more than the number of rings to switch ON. For example, if you have set switch3 OFF & Switch4 ON then number of initial rings to activate half of the board to switch ON the relays is 3 and number of initial rings to activate half of the board to switch OFF the relays is 3+1 = 4

      Switch1 Swtich2 Delay before making the second set of rings

      OFF OFF 20sec

      ON OFF 15sec

      OFF ON 10sec

      ON ON 5sec

      This is the maximum delay the board can take after it is half activated. It will reset after this delay.

      D) Now connect the circuit to the phone line and switch on its power supply.

      E) You can test the board now. For example set the DIP switch to Switch1 ON, Switch2 OFF (15 sec delay) & switch3 ON, switch4 OFF (4 rings to activate half for switching ON). If you want to switch ON relay 1 (connected to RB0 of main circuit) then you have to do the following:

      1. Give 4 rings and put down the receiver
      2. Wait 5 seconds (this 5 seconds wait is required to prevent the board from detecting continous rings)
      3. then within 15 seconds give 1 ring (1 ring for relay1, 2 rings for relay2 and so on) and put down the receiver
      4. then within 5 sec the relay1 will switch ON

      To switch off relay1:

      1. Give 5 rings and put down the receiver
      2. Wait 5 seconds (this 5 seconds wait is required to prevent the board from detecting continous rings)
      3. then within 15 seconds give 1 ring (1 ring for relay1, 2 rings for relay2 and so on) and put down the receiver
      4. then within 5 sec the relay1 will switch OFF

      IMPORTANT: This circuit has been tested by me and found to work correctly. I cannot guarantee that the circuit will work at your end since it depends on error free construction and usage. Please do not contact for any support and requests, any such requests will not be entertained.

      Thursday, September 17, 2009

      Simple PIC RF/Microwave Frequency Counter

      PIC RF/Microwave Frequency Counter
      This RF/Microwave Frequency Counter project built based on PIC 16F876A. The basic counter rate is extended to at least 180MHz using two 74Fxx devices. A divide-by-64 prescaler is used for higher frequencies up to at least 4.5GHz. All results of the measurement are shown on an inexpensive, 2x16 alphanumeric LCD module with large characters.

      There are 3 inpust on this project a microwave (prescaled) input, an RF input and a TTL input. The microwave and RF inputs are AC coupled and terminated to a low impedance (around 50ohms). The TTL input is DC coupled and has a high input impedance. A progress-bar indicator is provided on the LCD for the gate timing.

      Both the microwave and RF inputs have an additional feature : a simple signal-level detector driving yet another bar indicator on the LCD module. This is very useful to check for the correct input-signal level as well as an indicator for circuit tuning or absorption-wave-meter dip display (Lecher wires). This project designed by Matjaz Vidmar.

      tag : RF counter, Microwave Frequency counter, PIC project source

      Simple PIC RF/Microwave Frequency Counter

      PIC RF/Microwave Frequency Counter
      This RF/Microwave Frequency Counter project built based on PIC 16F876A. The basic counter rate is extended to at least 180MHz using two 74Fxx devices. A divide-by-64 prescaler is used for higher frequencies up to at least 4.5GHz. All results of the measurement are shown on an inexpensive, 2x16 alphanumeric LCD module with large characters.

      There are 3 inpust on this project a microwave (prescaled) input, an RF input and a TTL input. The microwave and RF inputs are AC coupled and terminated to a low impedance (around 50ohms). The TTL input is DC coupled and has a high input impedance. A progress-bar indicator is provided on the LCD for the gate timing.

      Both the microwave and RF inputs have an additional feature : a simple signal-level detector driving yet another bar indicator on the LCD module. This is very useful to check for the correct input-signal level as well as an indicator for circuit tuning or absorption-wave-meter dip display (Lecher wires). This project designed by Matjaz Vidmar.

      tag : RF counter, Microwave Frequency counter, PIC project source

      Sunday, August 30, 2009

      AVR Shark Tag Project

      microcontroller project animal tag
      The goal of this project was to develop a shark tag working bench-top microcontroller platform. It is to be used for on-animal, in-situ data logging applications involving sharks and potentially other large pelagic.

      The project used the Atmel Mega32 microcontroller to develop the core platform and functionality of a data archival tag. The project use temperature and pressure as sensor variable. The tasks ranged from logging sensor data to developing a simple user interface that requires only the addition of a laptop and a custom RS232 serial cable in the field.

      It used an off-the-shelf SD (Secure Digital) card using flash memory for large capacity multi-read/write data storage. The microcontroller’s ADCs (analog to digital converters) were used to convert analog voltages produced by select sensors into digital format.

      Tag: Animal Tag, shark, data logging, avr project src


      AVR Shark Tag Project

      microcontroller project animal tag
      The goal of this project was to develop a shark tag working bench-top microcontroller platform. It is to be used for on-animal, in-situ data logging applications involving sharks and potentially other large pelagic.

      The project used the Atmel Mega32 microcontroller to develop the core platform and functionality of a data archival tag. The project use temperature and pressure as sensor variable. The tasks ranged from logging sensor data to developing a simple user interface that requires only the addition of a laptop and a custom RS232 serial cable in the field.

      It used an off-the-shelf SD (Secure Digital) card using flash memory for large capacity multi-read/write data storage. The microcontroller’s ADCs (analog to digital converters) were used to convert analog voltages produced by select sensors into digital format.

      Tag: Animal Tag, shark, data logging, avr project src


      Thursday, August 13, 2009

      AVR Rotating Led Display

      Cool POV project : AVR Rotating Led Display


      If you like Rotating LED Display project, check out Rotating Led Display project by Aki Korhonen. He made POV project using modified 8 cm fan and microcontroller AVR AT mega as main part. To control the led, the project use 74HC595D shift registers. Not only can display the text this Rotating Led display can also demonstrate drawing and playable Pong game. Check the video below,





      tag: POV led display, rotating display, LED animation, AVR project (src)


      AVR Rotating Led Display

      Cool POV project : AVR Rotating Led Display


      If you like Rotating LED Display project, check out Rotating Led Display project by Aki Korhonen. He made POV project using modified 8 cm fan and microcontroller AVR AT mega as main part. To control the led, the project use 74HC595D shift registers. Not only can display the text this Rotating Led display can also demonstrate drawing and playable Pong game. Check the video below,





      tag: POV led display, rotating display, LED animation, AVR project (src)


      Sunday, August 2, 2009

      PIC Cactus LED Display

      LED Cactus Display PIC Project

      LEDactus is LED display project that resemble Cactus. It used PIC microcontroller 18F1320 as controller of the LED. LEDactus is immobile and attempts to survive by creating a pleasant display. It can produce more complex and mesmerizing displays. And in the latest generations, a sense of touch is added to allow the LEDactus to interact with passersby.

      term : LED display, electronic cactus, PIC project (src)

      PIC Cactus LED Display

      LED Cactus Display PIC Project

      LEDactus is LED display project that resemble Cactus. It used PIC microcontroller 18F1320 as controller of the LED. LEDactus is immobile and attempts to survive by creating a pleasant display. It can produce more complex and mesmerizing displays. And in the latest generations, a sense of touch is added to allow the LEDactus to interact with passersby.

      term : LED display, electronic cactus, PIC project (src)

      Tuesday, June 30, 2009

      PIC LCD Oscilloscope for Spectrum Analyzers

      PIC LCD Oscilloscope for Spectrum Analyzers
      This is simple and inexpensive LCD oscilloscope for spectrum analyzer display. The project use PIC 16F876A as main processor. Although a small LCD screen is not as good as analog oscilloscope, a LCD oscilloscope may be very useful in field measurements, for battery operation or you need different measurement at the same time along with oscilloscope.

      The 80dB scale of this LCD oscilloscope can be adjusted with the two trimmers providing the reference voltages to the A/D converter. The operation of the LCD oscilloscope is slightly different between the 80dB mode and the 40dB mode. In the 80dB mode, the trace is always visible and saturates on the bottom or top of screen. In the 40dB mode, the trace runs out of the screen and only the central part of the original 80dB scale is displayed. This project designed by Matjaz Vidmar.

      Download
      Source code, documentation and schematic

      tags : LCD, Oscilloscope, Spectrum Analyzer, PIC, microcontroller, project src

      Related Posts Plugin for WordPress, Blogger...